Match 6-inch GDP portals to your Ranger XP 1000 setup
For a Ranger XP 1000 build using larger tires, SuperATV's GDP Gen 3 portals place the reduction at the hubs and provide 6 inches of lift. Choose among 30%, 45% and 60% reduction options, with housing and idler choices shown in the product configuration.
Choose the gearing and housing
The 30% reduction places more emphasis on speed, 45% provides an intermediate reduction, and 60% is the largest reduction offered here. Match the choice to the complete tire and riding setup. Dual idlers spread gear load over an additional idler.
The reduction takes place at the hubs to reduce the load carried by upstream drivetrain components. The housings use gaskets or O-rings, a sealed input gear and a double-lipped output seal. Double-angular-contact output bearings and roller idler and drive bearings support the gear set. Steel-alloy backing plates are 5/16 inch thick.
Included components
- Four assembled portal boxes with 9310 gears, seals, output shafts, gaskets or O-rings, and thrust bearings
- Four universal hubs and stainless-steel slotted rotors with lugs
- Four steel-alloy backing plates and four steel caliper mounting plates
- Two steel steering arms
- Extended brake lines and required hardware, including a recessed castle-nut socket
- Frame stiffener only when selected in the product configuration
Tire size and supporting suspension
SuperATV lists these maximum tire sizes for the stated suspension combinations, measured at full compression and full steering turn. Treat the suspension requirements as part of the recommendation, not as optional extras.
- 30-inch tires: stock suspension
- 31-inch tires: 3-inch lift kit
- 33-inch tires: 1.5-inch forward front A-arms
- 34-inch tires: 1.5-inch forward front A-arms with a 3-inch lift kit
- 38-inch tires: 6-inch lift kit
The supplier notes that larger tires may require trimming or may rub. Check the wheel requirements and model-specific exclusions in the fitment information before ordering.
Before you order
Use the wheel requirements and tire-size guide below before choosing the complete package. The optional frame stiffener does not fit the High Lifter Edition.
Specifications and features
- Available with billet or cast aluminum housings
- Dual idler gear configuration maximizes strength
- Cool, quiet, precision-ground gears made from 9310 alloy billet steel
- 1.5 in. diameter 4340 hardened steel drive shaft
- Housings use advanced gaskets or O-rings that don’t let anything through
- Universal hubs can be set up to work with the following bolt patterns: 4/156, 4/137, 4/115, and 4/110
- Gear reduction reduces stress on your drivetrain
- Dual idler gear configuration adds a 1” front and rear offset—2” total extension
- Lighter than the competition
Fitment information
- Polaris Ranger XP 1000 : 2017+
- Polaris Ranger XP 1000 Crew : 2017+
- Polaris Ranger XP 1000 Back Country : 2019
- Polaris Ranger XP 1000 Back Country Crew : 2019
- Polaris Ranger XP 1000 Big Game Edition : 2021+
- Polaris Ranger XP 1000 Big Game Edition Crew : 2021+
- Polaris Ranger XP 1000 High Lifter : 2017+
- Polaris Ranger XP 1000 High Lifter Crew : 2017+
- Polaris Ranger XP 1000 Northstar Edition : 2017-2020
- Polaris Ranger XP 1000 Northstar Edition Crew : 2017-2020
- Polaris Ranger XP 1000 Northstar Premium: 2021+
- Polaris Ranger XP 1000 Northstar Premium Crew: 2021+
- Polaris Ranger XP 1000 NorthStar Ultimate : 2021+
- Polaris Ranger XP 1000 NorthStar Ultimate Crew : 2021+
- Polaris Ranger XP 1000 Texas Edition : 2020+
- Polaris Ranger XP 1000 Texas Edition Crew : 2020+
- Polaris Ranger XP 1000 Trail Boss : 2021+
- Polaris Ranger XP 1000 Trail Boss Crew : 2021+
- Polaris Ranger XP 1000 Waterfowl Edition : 2021+
- Polaris Ranger XP 1000 Waterfowl Edition Crew : 2021+
- NOTE
- Frame stiffener does NOT fit High Lifter Edition
- For an existing or planned RIDE System Rear Steering Kit, confirm the compatible portal components with SuperATV before ordering.
- Wheel Requirements:
- 18” or larger wheel required
- 18” wheels cannot exceed 4-1/2” backspacing
- 20” and larger wheels cannot exceed 5” backspacing
- Wheels need to have a center hole of at least 3.25" (82.55mm) or require a 1” wheel spacer
